[Angstrom-devel] BeagleBoard (C3) won't boot
Koen Kooi
koen at dominion.thruhere.net
Sat May 28 12:35:06 CEST 2011
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
On 28-05-11 12:07, Gary Thomas wrote:
> I just built Angstrom via oe-core for the BeagleBoard, rev C3 (not xM)
> Here were my steps:
> $ git clone git://git.angstrom-distribution.org/setup-scripts angstrom-bb
> $ cd angstrom-bb
> $ git checkout -b local-oe origin/oe-core
> $ MACHINE=beagleboard ./oebb.sh config beagleboard
> $ MACHINE=beagleboard ./oebb.sh bitbake console-image
>
> It doesn't boot at all. I built a bootable SD from the deploy/images,
> including MLO and U-Boot. Here's the boot sequence (I broke in to set
> the console):
> Texas Instruments X-Loader 1.4.4ss (Jan 29 2011 - 10:54:03)
That should say 1.5.0, but wouldn't cause boot problems.
For reference, this is what I get on my C3:
Texas Instruments X-Loader 1.5.0 (May 23 2011 - 13:53:21)
Beagle Rev C1/C2/C3
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2011.03-rc1-00000-g5ace684-dirty (May 15 2011 - 18:50:56)
OMAP3530-GP ES3.0, CPU-OPP2, L3-165MHz, Max CPU Clock 600 mHz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 256 MiB
NAND: 256 MiB
MMC: OMAP SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Beagle Rev C1/C2/C3
Recognized Tincantools Zippy board (rev 1 )
Die ID #4088000300000000040323090d01c015
Hit any key to stop autoboot: 3 2 1 0
The user button is currently NOT pressed.
SD/MMC found on device 0
reading uEnv.txt
MMC: block number 0x10000906 exceeds max(0x3af000)
** Unable to read "uEnv.txt" from mmc 0:1 **
Loading file "/boot/uImage" from mmc device 0:2 (xxa2)
3329956 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 80200000 ...
Image Name: Angstrom/2.6.39/beagleboard
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3329892 Bytes = 3.2 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.39+ (koen at dominion) (gcc version 4.5.3
(GCC) ) #2 Thu May 26 17:18:00 CEST 2011
[ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7),
cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing
instruction cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] Beagle expansionboard: zippy
[ 0.000000] Reserving 12582912 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3430/3530 ES3.0 (l2cache iva sgx neon isp )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
[ 0.000000] Reprogramming SDRC clock to 332000000 Hz
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 61952
[ 0.000000] Kernel command line: console=ttyO2,115200n8 mpurate=auto
buddy=zippy camera=lbcm3m1 vram=12M omapfb.mode=dvi:640x480MR-16 at 60
omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] allocated 1048576 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't
want memory cgroups
[ 0.000000] Memory: 244MB = 244MB total
[ 0.000000] Memory: 239680k/239680k available, 22464k reserved, 0K
highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc003d000 ( 212 kB)
[ 0.000000] .text : 0xc003d000 - 0xc062c7ec (6078 kB)
[ 0.000000] .data : 0xc062e000 - 0xc0679900 ( 303 kB)
[ 0.000000] NR_IRQS:410
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck.
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps
every 131071999ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000244] Calibrating delay loop... 475.76 BogoMIPS (lpj=1855488)
[ 0.044799] pid_max: default: 32768 minimum: 301
[ 0.045043] Mount-cache hash table entries: 512
[ 0.045532] Initializing cgroup subsys ns
[ 0.045532] ns_cgroup deprecated: consider using the 'clone_children'
flag without the ns_cgroup.
[ 0.045562] Initializing cgroup subsys cpuacct
[ 0.045593] Initializing cgroup subsys memory
[ 0.045654] Initializing cgroup subsys devices
[ 0.045684] Initializing cgroup subsys freezer
[ 0.045684] Initializing cgroup subsys blkio
[ 0.045715] Initializing cgroup subsys perf_event
[ 0.045837] CPU: Testing write buffer coherency: ok
[ 0.046905] devtmpfs: initialized
[ 0.048492] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_core
[ 0.048522] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_per
[ 0.048522] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for
l4_wkup
[ 0.063873] omap_hwmod: i2c1: softreset failed (waited 10000 usec)
[ 0.077911] omap_hwmod: i2c2: softreset failed (waited 10000 usec)
[ 0.091949] omap_hwmod: i2c3: softreset failed (waited 10000 usec)
[ 0.093353] print_constraints: dummy:
[ 0.093658] NET: Registered protocol family 16
[ 0.093872] GPMC revision 5.0
[ 0.095245] OMAP GPIO hardware version 2.5
[ 0.095367] OMAP GPIO hardware version 2.5
[ 0.095520] OMAP GPIO hardware version 2.5
[ 0.095642] OMAP GPIO hardware version 2.5
[ 0.095764] OMAP GPIO hardware version 2.5
[ 0.095886] OMAP GPIO hardware version 2.5
[ 0.097442] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.097564] OMAP3 Beagle Rev: C1/C2/C3
[ 0.099975] omap_device: omap_uart.2: new worst case deactivate
latency 0: 30517
[ 0.100067] Beagle expansionboard: initializing enc28j60
[ 0.100219] Beagle expansionboard: assigning GPIO 141 and 162 to MMC1
[ 0.100524] Found NAND on CS0
[ 0.100524] Registering NAND on CS0
[ 0.100677] Unable to get DVI reset GPIO
[ 0.100738] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.104309] OMAP DMA hardware revision 4.0
[ 0.116424] bio: create slab <bio-0> at 0
[ 0.117919] SCSI subsystem initialized
[ 0.119934] usbcore: registered new interface driver usbfs
[ 0.120117] usbcore: registered new interface driver hub
[ 0.120361] usbcore: registered new device driver usb
[ 0.121032] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz
[ 0.123931] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.123992] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.124542] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.126953] print_constraints: VUSB1V5: 1500 mV normal standby
[ 0.127532] print_constraints: VUSB1V8: 1800 mV normal standby
[ 0.128021] print_constraints: VUSB3V1: 3100 mV normal standby
[ 0.130096] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 0.130950] print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV
normal standby
[ 0.131530] print_constraints: VDAC: 1800 mV normal standby
[ 0.132049] print_constraints: VDVI: 1800 mV normal standby
[ 0.132690] print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV
normal standby
[ 0.133300] print_constraints: VAUX3: 1800 mV normal standby
[ 0.133880] print_constraints: VAUX4: 1800 mV normal standby
[ 0.134094] omap_device: omap_i2c.1: new worst case deactivate
latency 0: 30517
[ 0.141937] omap_i2c omap_i2c.2: bus 2 rev3.12 at 100 kHz
[ 0.156829] omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz
[ 0.157775] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.158569] Bluetooth: Core ver 2.16
[ 0.158660] NET: Registered protocol family 31
[ 0.158660] Bluetooth: HCI device and connection manager initialized
[ 0.158691] Bluetooth: HCI socket layer initialized
[ 0.158691] Bluetooth: L2CAP socket layer initialized
[ 0.158905] Bluetooth: SCO socket layer initialized
[ 0.159271] Switching to clocksource 32k_counter
[ 0.164489] Switched to NOHz mode on CPU #0
[ 0.175262] musb-hdrc: version 6.0, musb-dma, otg (peripheral+host),
debug=0
[ 0.178985] musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000
using DMA, IRQ 92
[ 0.179718] NET: Registered protocol family 2
[ 0.179962] IP route cache hash table entries: 2048 (order: 1, 8192
bytes)
[ 0.180480] TCP established hash table entries: 8192 (order: 4, 65536
bytes)
[ 0.180694] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.180847] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.180847] TCP reno registered
[ 0.180877] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180908] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.181365] NET: Registered protocol family 1
[ 0.182708] RPC: Registered udp transport module.
[ 0.182739] RPC: Registered tcp transport module.
[ 0.182739] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.184143] omap-iommu omap-iommu.0: isp registered
[ 0.186157] VFS: Disk quotas dquot_6.5.2
[ 0.186218] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.187011] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.187469] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.187499] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat,
Inc.
[ 0.188354] msgmni has been set to 468
[ 0.190490] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 0.190826] io scheduler noop registered
[ 0.190856] io scheduler deadline registered
[ 0.190948] io scheduler cfq registered (default)
[ 0.253173] OMAP DSS rev 2.0
[ 0.583557] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.590087] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a
OMAP UART0
[ 0.591491] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a
OMAP UART1
[ 0.592834] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a
OMAP UART2
[ 1.410430] console [ttyO2] enabled
[ 1.455108] brd: module loaded
[ 1.478546] loop: module loaded
[ 1.488067] omap2-nand driver initializing
[ 1.493133] ONFI flash detected
[ 1.497192] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron
NAND 256MiB 1,8V 16-bit)
[ 1.508087] cmdlinepart partition parsing not available
[ 1.513916] Creating 5 MTD partitions on "omap2-nand.0":
[ 1.519866] 0x000000000000-0x000000080000 : "X-Loader"
[ 1.531433] 0x000000080000-0x000000260000 : "U-Boot"
[ 1.543273] 0x000000260000-0x000000280000 : "U-Boot Env"
[ 1.554260] 0x000000280000-0x000000680000 : "Kernel"
[ 1.566833] 0x000000680000-0x000010000000 : "File System"
[ 1.690948] enc28j60 spi4.0: enc28j60 Ethernet driver 1.01 loaded
[ 1.697998] omap_device: omap2_mcspi.4: new worst case deactivate
latency 0: 30517
[ 1.713806] omap_device: omap2_mcspi.4: new worst case deactivate
latency 0: 61035
[ 1.724060] enc28j60 spi4.0: eth0: Features changed: 0x00004800 ->
0x00004000
[ 1.732177] net eth0: enc28j60 driver registered
[ 1.737518] usbcore: registered new interface driver catc
[ 1.743560] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[ 1.750244] usbcore: registered new interface driver kaweth
[ 1.756500] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB
Ethernet driver
[ 1.764923] usbcore: registered new interface driver pegasus
[ 1.771240] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet
driver
[ 1.778991] usbcore: registered new interface driver rtl8150
[ 1.785400] usbcore: registered new interface driver asix
[ 1.791503] usbcore: registered new interface driver cdc_ether
[ 1.798095] usbcore: registered new interface driver dm9601
[ 1.804412] usbcore: registered new interface driver smsc95xx
[ 1.810943] usbcore: registered new interface driver gl620a
[ 1.817260] usbcore: registered new interface driver net1080
[ 1.823669] usbcore: registered new interface driver plusb
[ 1.829833] usbcore: registered new interface driver rndis_host
[ 1.836547] usbcore: registered new interface driver cdc_subset
[ 1.843231] usbcore: registered new interface driver zaurus
[ 1.849548] usbcore: registered new interface driver MOSCHIP
usb-ethernet driver
[ 1.858428] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.865844] _regulator_get: ehci-omap.0 supply hsusb0 not found,
using dummy regulator
[ 1.874755] _regulator_get: ehci-omap.0 supply hsusb1 not found,
using dummy regulator
[ 3.893737] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 3.900451] ehci-omap ehci-omap.0: new USB bus registered, assigned
bus number 1
[ 3.908905] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 3.925048] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 3.931549] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.939147] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.947235] usb usb1: Product: OMAP-EHCI Host Controller
[ 3.953155] usb usb1: Manufacturer: Linux 2.6.39+ ehci_hcd
[ 3.959289] usb usb1: SerialNumber: ehci-omap.0
[ 3.965148] hub 1-0:1.0: USB hub found
[ 3.969360] hub 1-0:1.0: 3 ports detected
[ 4.003204] Initializing USB Mass Storage driver...
[ 4.008819] usbcore: registered new interface driver usb-storage
[ 4.015563] USB Mass Storage support registered.
[ 4.021179] mousedev: PS/2 mouse device common for all mice
[ 4.027984] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 4.037078] input: twl4030_pwrbutton as
/devices/platform/omap/omap_i2c.1/i2c-1/1-0049/twl4030_pwrbutton/input/input1
[ 4.052032] rtc-ds1307 2-0068: rtc core: registered ds1307 as rtc0
[ 4.058959] rtc-ds1307 2-0068: 56 bytes nvram
[ 4.063873] i2c /dev entries driver
[ 4.068481] Linux media interface: v0.10
[ 4.072937] Linux video capture interface: v2.00
[ 4.078521] vpfe_init
[ 4.081756] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[ 4.088531] Bluetooth: HCI UART driver ver 2.2
[ 4.093536] Bluetooth: HCI H4 protocol initialized
[ 4.098876] Bluetooth: HCI BCSP protocol initialized
[ 4.104431] Bluetooth: HCILL protocol initialized
[ 4.109680] Bluetooth: HCIATH3K protocol initialized
[ 4.115234] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 4.121582] usbcore: registered new interface driver btusb
[ 4.127746] cpuidle: using governor ladder
[ 4.132354] cpuidle: using governor menu
[ 4.139556] _regulator_get: omap_hsmmc.1 supply vmmc not found, using
dummy regulator
[ 4.148956] _regulator_get: omap_hsmmc.1 supply vmmc_aux not found,
using dummy regulator
[ 4.161041] usbcore: registered new interface driver usbhid
[ 4.167297] usbhid: USB HID core driver
[ 4.172119] usbcore: registered new interface driver snd-usb-audio
[ 4.179870] OMAP3 Beagle/Devkit8000 SoC init
[ 4.195831] asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok
[ 4.205993] ALSA device list:
[ 4.209350] #0: omap3beagle
[ 4.212677] oprofile: hardware counters not available
[ 4.218322] oprofile: using timer interrupt.
[ 4.223297] TCP cubic registered
[ 4.226898] NET: Registered protocol family 17
[ 4.231964] NET: Registered protocol family 15
[ 4.236938] lib80211: common routines for IEEE802.11 drivers
[ 4.243408] Registering the dns_resolver key type
[ 4.248748] VFP support v0.3: implementor 41 architecture 3 part 30
variant c rev 1
[ 4.257446] ThumbEE CPU extension supported.
[ 4.265045] Power Management for TI OMAP3.
[ 4.270416] sr_init: No PMIC hook to init smartreflex
[ 4.276245] smartreflex smartreflex.0: omap_sr_probe: SmartReflex
driver initialized
[ 4.285369] smartreflex smartreflex.1: omap_sr_probe: SmartReflex
driver initialized
[ 4.294189] SmartReflex Class3 initialized
[ 4.300109] usb 1-2: new high speed USB device number 2 using ehci-omap
[ 4.326049] clock: disabling unused clocks to save power
[ 4.333068] registered taskstats version 1
[ 4.338684] fbcvt: 640x480 at 60: CVT Name - .307M3-R
[ 4.359008] Console: switching to colour frame buffer device 80x30
[ 4.389892] regulator_init_complete: VAUX3: incomplete constraints,
leaving on
[ 4.398620] regulator_init_complete: VDAC: incomplete constraints,
leaving on
[ 4.408691] rtc-ds1307 2-0068: setting system clock to 2000-01-06
02:34:06 UTC (947126046)
[ 4.418151] omap_vout omap_vout: Buffer Size = 3686400
[ 4.425201] omap_vout omap_vout: : registered and initialized video
device 0
[ 4.433776] Waiting for root device /dev/mmcblk0p2...
[ 4.488403] usb 1-2: New USB device found, idVendor=04e1, idProduct=0201
[ 4.495910] usb 1-2: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 4.505310] hub 1-2:1.0: USB hub found
[ 4.509490] hub 1-2:1.0: 4 ports detected
[ 4.628326] mmc0: new high speed SD card at address aaaa
[ 4.634521] mmcblk0: mmc0:aaaa SD02G 1.84 GiB
[ 4.639831] mmcblk0: detected capacity change from 0 to 1977614336
[ 4.648162] mmcblk0: p1 p2
[ 4.765350] EXT3-fs: barriers not enabled
[ 4.800567] usb 1-2.1: new low speed USB device number 3 using ehci-omap
[ 4.952178] usb 1-2.1: New USB device found, idVendor=04f2,
idProduct=0402
[ 4.959716] usb 1-2.1: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 4.967803] usb 1-2.1: Product: USB Keyboard
[ 4.972503] usb 1-2.1: Manufacturer: Chicony
[ 5.002349] input: Chicony USB Keyboard as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.1/1-2.1:1.0/input/input2
[ 5.016265] generic-usb 0003:04F2:0402.0001: input: USB HID v1.11
Keyboard [Chicony USB Keyboard] on usb-ehci-omap.0-2.1/input0
[ 5.072113] input: Chicony USB Keyboard as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.1/1-2.1:1.1/input/input3
[ 5.085845] generic-usb 0003:04F2:0402.0002: input: USB HID v1.11
Device [Chicony USB Keyboard] on usb-ehci-omap.0-2.1/input1
[ 5.184234] usb 1-2.2: new high speed USB device number 4 using ehci-omap
[ 5.339447] usb 1-2.2: New USB device found, idVendor=145f,
idProduct=0142
[ 5.346984] usb 1-2.2: New USB device strings: Mfr=2, Product=1,
SerialNumber=0
[ 5.355133] usb 1-2.2: Product: Trust WB-6250X Webcam
[ 5.360595] usb 1-2.2: Manufacturer:
[ 5.404510] 4:3:1: cannot get freq at ep 0x84
[ 5.503875] usb 1-2.3: new low speed USB device number 5 using ehci-omap
[ 5.636047] usb 1-2.3: New USB device found, idVendor=046d,
idProduct=c00e
[ 5.643524] usb 1-2.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 5.651794] usb 1-2.3: Product: USB-PS/2 Optical Mouse
[ 5.657318] usb 1-2.3: Manufacturer: Logitech
[ 5.681152] input: Logitech USB-PS/2 Optical Mouse as
/devices/platform/usbhs-omap.0/ehci-omap.0/usb1/1-2/1-2.3/1-2.3:1.0/input/input4
[ 5.696807] generic-usb 0003:046D:C00E.0003: input: USB HID v1.10
Mouse [Logitech USB-PS/2 Optical Mouse] on usb-ehci-omap.0-2.3/input0
[ 5.965606] kjournald starting. Commit interval 5 seconds
[ 6.152587] EXT3-fs (mmcblk0p2): using internal journal
[ 6.158203] EXT3-fs (mmcblk0p2): recovery complete
[ 6.175140] EXT3-fs (mmcblk0p2): mounted filesystem with writeback
data mode
[ 6.182983] VFS: Mounted root (ext3 filesystem) on device 179:2.
[ 6.193939] devtmpfs: mounted
[ 6.197509] Freeing init memory: 212K
[ 6.524017] systemd[1]: systemd 28 running in system mode. (+PAM
+LIBWRAP -AUDIT -SELINUX +SYSVINIT -LIBCRYPTSETUP; angstrom)
Welcome to The Ångström Distribution!
[ 6.669219] systemd[1]: Set hostname to <tentacle-systemd>.
Starting udev Kernel Device Manager...
Starting Apply Kernel Variables...
Started Load Kernel Modules.
... etc ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (Darwin)
iD8DBQFN4M/ZMkyGM64RGpERAl04AKC1ZwD2iXifbX0sfqkvQtN8t7DWPQCfYo3s
tMSl/1jS3JllQ3Ap+TuynGw=
=Stg4
-----END PGP SIGNATURE-----
More information about the Angstrom-distro-devel
mailing list